Bearon Aquatics "Formerly PowerHouse" Ice Eater: P1000

How it works

The Ice Eater’s propeller draws up warmer subsurface water and deflects it to the surface creating a constant circulation of warmer water that prevents ice formation and melts existing ice.
The design of the Ice Eater’s venturi shroud (white housing) with outwardly flared ends, provides more upward thrust & draws warmer water from greater depths than other conventional de-icers.

Why buy the original De-Icer?

Ice Eater is shipped complete with suspension lines and shackles. Therefore, it can be taken out of the box, hung from a boat, dock, or pier and plugged in.
Unlike other de-icing units, Ice Eater requires no additional hardware to obtain the desired de-icing pattern. Just move a shackle from one hole to another hole on the top rim, and you can quickly change the angle the Ice Eater is suspended at.
The average operating depth of the Ice Eater is between two and three feet, but for best performance, ensure there is at least one foot between the Ice Eater and the seabed.

• Custom Designed and Engineered for maximum efficiency and performance in all climates.
• Agitates more fresh-water & salt-water than any other de-icer on the market.
• Patented heavy duty PVC Venturi Housing designed for superior water flow and protection of the motor and propeller
• Bronze End-bell ensures a long life without cracking or warping.
• Quick Disconnect Power Cord allows for easy replacement.
• Environmentally Friendly Dielectric Lubricating Fluid is non-toxic and biodegradable.
• 3-Year Warranty – Best Warranty in the Industry

Model P1000 Specifications:

• Horse Power: 1.0
• Hertz: 50/60
• Running Amps: 7.0 Amps (115V) / 3.5 Amps (230V)
• Open Diameter: 80′ (Open Diameter based on normal winter conditions)
• Pounds of Thrust: 36
• Gallons per Minute: 1400
• Revolutions per Minute: 1650
• Weight 43 lbs
• Dimensions 15 × 15 × 17 inches

Design Features

• The design of the Ice Eater’s venturi shroud (housing) with outwardly flared ends, provides more upward thrust & draws warmer water from greater depths than other conventional de-icers.
• The shroud is submersible below the surface either vertically or angled from vertical. A set of mounting holes at opposed positions on the flange allows the lines to be attached.
• The Power House is committed to providing the finest de-icers available in the marketplace. As a result, specifications are subject to change without notice.

Marina De-Icing
• Ice Eater de-icers are custom designed and engineered for maximum performance.
• Our units are designed to agitate fresh or salt water at maximum efficiency in all climatic conditions.
• Our energy efficient Ice Eater’s will agitate more water than any de-icer on the market today.
• We ship by U.P.S. or motor freight.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Ice Eater products:

• Warranty Period: Three (3) years from the date of manufacture by Bearon.
• If a unit is used for purposes other than de-icing, then a one (1) year limited warranty shall apply.
• NOTE: There are certain conditions under which no circulator/de-icer can prevent ice damage, such as ice
that moves as a result of wind or current, extremely cold weather where ice forms all the way to the
bottom, and in some cases, where the bottom temperature is the same as the ice (very shallow water).
The operation efficiency will be somewhat reduced when the flow is restricted by allowing too little
bottom clearance.

• In areas of high salinity, high electrical current, and/or warm temperatures, a Bearon electrolysis kit must be
mounted to the stainless steel can.
• In addition to the limitations above, this limited warranty does not include any defects or failures of the sacrificial
anode, ropes, power cord, propeller, or brackets. The warranty will be voided if the sacrificial anode around the
propeller, shaft, and/or stainless steel can shows significant deterioration. Failure to keep the shaft and can clear
of debris (including string, bags, calcium buildup, barnacles, etc.); or the propeller shows signs of excessive or
unusual wear and tear.
• Failure to inspect and replace anodes constitutes misuse.
• Complete units must be shipped for evaluation.
• The evaluation fee is $65.